Traxis
DBS1500 & DBS2550 Information & Re-Scan
Instructions:
I Pre-Program the receivers
that I sell and I EDIT the Radio Channel List, so
that the Talk Radio Shows are at the Top of the Radio
List. If you Re-Scan the Satellite or a certain
Frequency that the channels are on, it will change
the name of the channel and put them in a different
location in the list. You can EDIT the list and the
names of the channels to what you like and move them
back up to the top of the list, after you Re-Scan
them.
Step by Step Instructions to
Re-Scan the Frequency of 11836MHz Vertical SR20765
& 12115MHz Vertical SR22425.
These are the main frequencies where most of the Talk
Radio Channels are located.
Hit the MENU button on the
Remote control. This will bring up first page of the
MENU .
Right Arrow Once to the
INSTALLATION screen of the MENU.
Be Careful here, not to enter the ANTENNA
INSTALLATION part of the menu. If you make changes
here, you might erase your channels.
Settings in this part of the menu must be set
correctly to be able to receive the channels.
Down Arrow 2 times to the
TRANSPONDER MANAGER and Hit OK.
Down Arrow in the TP List
until you find the Frequency of 11836. On most Traxis
receivers, this is line 16. In some earlier models,
it may be line 15.
Look at the 2 signal bars in
the lower right corner and verify that you have Level
and Quality. Quality is the Important one. This
verifies that you are getting the signal and the
Quality should read from 45 to 75%. The higher the
better.
Hit the BLUE button on the
Lower Right Corner of the Remote Control.
This will bring up the Search Option Menu. By
default, it will be set to ALL. Use your Right Arrow
and change this to FREE. This will keep you from
scanning in Scrambled Channels.
Hit the OK button on the Remote and the receiver will
Re-Scan the Frequency.
After it is done scanning, Hit
the EXIT button repeatedly, until you are completely
out of the MENU and the receiver will Update the Data
base and your new channels will have been added.
Now you can repeat the steps
above, but this time when you are in the Transponder
Manager, go down in the TP List, until you find the
frequency of 12115 and then repeat the same procedure
to scan in the New, "We The People Radio
Network."
When you first got your
receiver, below is what the channels were named and
what stations were on them and what the new names of
the channels will be now that you have Re-Scanned
them:
Global Star 1 was World Wide
First Amendment Radio on Right Audio & Scriptures
For America on Left Audio. After Re-Scanning, this
station will now be named: Star 1 & Star 2.
Global Star 2 was programming
from GCN on Right Audio & the Overcomer Network
on Left Audio. After Re-Scanning, this station will
now be named: Overcomer / Star 4.
Global Star 3 was programming
from GCN on Right Audio & Americas Voice Radio on
Left Audio. After Re-Scanning, this station will now
be named: Star 5 & AVR
Global Star 4 was RBN in
Stereo. After Re-Scanning, this station will now be
named: RBN radio.
You will have to go through
your list of Radio Channels to find the new names.
You can leave them where they are, or you can EDIT
your list and move them back up to the top and even
renamed them again if you like. Follow the
instructions below to do this.
Hit MENU
Hit OK to the Channel Manager
Hit the RED Button in the
lower Left corner of the Remote, which is the SORT
Function. This will bring up the Sort function menu.
Cursor down to the line that says, Manul and Hit OK.
This will allow you to manually sort the channels in
the list.
Cursor through the channel
list using your Up or Down Arrow until you find the
channel that you want to move up to the number 1
position. When you find the channel, Hit the OK
button. This will put an Up and Down Arrow to the
Right of the Channel Name. Now you can cursor up to
the Number 1 position and the channel name will go up
with you and when you get to the Number 1 position,
Hit OK and it will put the channel at the top of the
list and make it become channel Number 1.
Follow this same procedure
with the remaining channels that you want to move.
After you have the channels
back up in the top of the list, you can also rename
or EDIT them if you like.
Highlight the channel you want
to rename or EDIT and hit the YELLOW button on the
remote control. This brings up the Channel Manager
Menu and the top line will already be Highlighted.
Hit OK and it will bring up a
box of all of the Letters and Numbers that you use to
Change the name with. Cursor through the letters and
numbers and highlight the First Letter you want to
use and Hit the OK button. Then cursor to the next
Letter and Hit the OK button again. Continue this
procedure until you have spelled the name you want to
use. There is an option in the Box to put a Space in
between the Name and Number and all you have to do is
highlight it and Hit OK and it will put a Space in.
When you are done putting in the Letters and Numbers
that you want to use, then highlight the Save box and
hit OK. Your new Channel Name will now be in the Top
Box of the Menu.
Now Hit EXIT and it will take
you back to the channel list, where you can select
the next channel that you wish to EDIT and follow the
procedure above. Continue this until you are done
EDITING all of the channels that you want and then
completely EXIT the MENU. You will have to Hit the
EXIT button 2 or 3 times to completely EXIT the MENU.
When you do Exit, the receiver will save all of your
changes to the data base and you will be ready to get
back to listening to the Shows!
Pansat
2700A & 3500SD Information & Re-Scan
Instructions:
I Pre-Program the receivers
that I sell and I EDIT the Radio Channel List, so
that the Talk Radio Shows are at the Top of the Radio
List. If you Re-Scan the Satellite or a certain
Frequency that the channels are on, it will change
the name of the channel and put them in a different
location in the list. You can EDIT the list and the
names of the channels to what you like and move them
back up to the top of the list, after you Re-Scan
them.
Step by Step Instructions to
Re-Scan the Frequency of 11836MHz Vertical SR20765.
This is the main frequency where most of the Talk
Radio Channels are located.
Hit the MENU button on the
Remote control. This will bring up first page of the
MENU .
Hit OK on Installation. The
receiver will ask you for the Password, which is 0 -
0 - 0 - 0.
Cursor down to the line that
says, TP Scan and Hit OK.
A list will come up on the
right side of the screen with the Names of the
Satellites that are programmed in the receiver.
Select the satellite named, T-5/Ku or if you have the
newest version of software, this satellite is now
named Galaxy 25/Ku, then Hit OK.
Cursor down in the list of
frequencies, until you find 11836 V 20.765 and
Highlight it and Hit the OK button on the Remote
Control. The receiver will then Re-Scan the frequency
you have selected and will add any new stations that
have started broadcasting to the end of the Radio
Channel list.
Then Hit EXIT repeatedly,
until you are completely out of the MENU.
Your New Channels will be
added to the end of the Radio List.
Now you can repeat the steps
above, but this time when you are in the TP Scan, go
down in the List, until you find the frequency of
12115 and then repeat the same procedure to scan in
the New, "We The People Radio Network."
You can then EDIT the new
channel/s and rename it or move it in your channel
list by doing the following:
Hit the MENU button on the
Remote control. This will bring up first page of the
MENU .
Cursor down to the line that
says Channel Edit and Hit OK. The receiver will ask
you for the Password, which is 0 - 0 - 0 - 0. This
will take you into the Channel Edit portion of the
Menu, where you can Sort, Move, Delete, Make Favorite
Lists, Do Parental Locks, Skip and Rename Channels.
To move a channel, cursor down
to the word Move and Hit OK. This will move your
cursor over to the list of channels. Now cursor
through the list, until you find the channel that you
want to move and then Hit OK. This will move the
channel name to the right of the list and allow you
to cursor up or down in the list and take the channel
with you. Move until you find the position in the
list where you want to put it and then Hit OK and the
channel will now be in that position in the list.
When you are done, then just EXIT out of the MENU.
If you want to Rename the
channel, follow the same steps listed above to get
into the Channel Edit Menu and cursor down to Rename
and Hit OK. Your cursor will move over to the list of
channel names and then cursor through the list until
you find the channel you want to rename and Hit OK.
This will bring up a box of letters and numbers that
you can cursor through and type the name in that you
want to use. When you are done typing the name,
cursor down to the bottom line in the box and
highlight the OK icon and hit the OK button on the
remote control.
Then Hit EXIT repeatedly,
until you are completely out of the MENU.
You can also do a SMART Search
with the Pansat receivers and the receiver will
automatically search for any new TV and Radio
channels. You access SMART Search through the
Installation Menu.
